Stopping Distance Calculator screenshot

Stopping Distance Calculator

Compute reaction, braking, and total stop distance by road.

Privacy First
0 Runs
Updated 2026-11-07
Runs in your browser
No upload
No account needed
Recalculates as you type

Compute reaction, braking, and total stop distance by road. Enter your numbers and get an instant result.

Enter a speed in miles or kilometres per hour and choose a road surface, and the page splits the stopping distance into a reaction distance and a braking distance, reporting both in feet and metres.

The reaction distance is the speed in metres per second multiplied by 1.5 seconds. The braking distance is the square of that speed divided by twice the gravitational constant and the friction coefficient, with 0.7 for dry asphalt, 0.4 for a wet surface and 0.15 for ice or snow.

The two are added for the total. The page models a single vehicle on a level road with a fixed reaction time; it does not include gradient, load, tyre condition, ABS behaviour or the difference between a alert and a distracted driver.

The three inputs

Speed is converted to metres per second before any arithmetic: a value in mph is multiplied by 1.60934 and then divided by 3.6, and a value already in km/h is only divided by 3.6. Negative or non-numeric input clears the result.

The surface sets the friction coefficient, and that coefficient is the largest single influence on the braking half. Ice at 0.15 produces a braking distance more than four times the dry figure at the same speed, because the distance is inversely proportional to friction.

  • Reaction time: 1.5 seconds, fixed
  • Friction: 0.7 dry, 0.4 wet, 0.15 ice or snow
  • Output: reaction, braking and total, in feet and metres

Why this is a planning figure

A real stop depends on the driver noticing, deciding and pressing, on the tyres and their temperature, on the road's camber and on whether the brakes are warm. A single coefficient cannot represent that, and the page does not pretend to.

The 1.5-second reaction time is a common planning value, not a measurement of any particular driver. A tired or distracted driver is slower, and a trained one may be faster; changing the constant would change the total, and the form does not offer it.

How to use the two inputs

Type the speed into Vehicle Speed, choose MPH or KM/H for the unit, and pick the road surface: Dry Asphalt, Wet Surface, or Ice and Snow. The reaction, braking and total distances recompute as the inputs change, shown in feet and metres side by side.

Compare surfaces at the same speed by switching the selector and watching the braking half move: ice at 0.15 stretches it to more than four times the dry figure. Use the total as a planning estimate, not as a following distance for a real road.

What to Expect

Best for

  • A first estimate of stopping distance at a given speed
  • Showing how much ice changes the braking half
  • A teaching example of the square relationship with speed

Not ideal for

  • An accident reconstruction, which needs measured friction and timing
  • A vehicle with a different reaction time or a gradient
  • A legal or insurance determination

What this tool keeps

  • The arithmetic from the two inputs, with no rounding between steps
  • The same three surfaces and their fixed coefficients
  • Feet and metres side by side for the same distance

What may need cleanup

  • The reaction time, which is fixed at 1.5 seconds
  • The friction coefficient, which is a representative value rather than a measurement
  • The total, which assumes level ground and a straight stop

Common errors

  • Doubling the speed and expecting double the braking distance, which is four times
  • Reading the total as a legal safe following distance
  • Using the dry coefficient for a wet road because the selector was left alone

Example use cases

  • A driving lesson on following distance
  • A road-safety poster's example
  • Comparing a dry and an icy stop at the same speed

Sample input

A speed of 60 mph on dry asphalt, the page's starting values.

Sample output

A total stopping distance of about 93 metres, split into roughly 40 metres of reaction and 52 metres of braking, and shown in feet as well.

Who this is for

  • Driving instructors
  • Road-safety educators
  • Drivers curious about the square law

Frequently asked questions

What goes into the stopping distance figure?

A reaction distance and a braking distance, split from the speed you enter and a chosen road surface, reported in feet and metres.

Is it an accident reconstruction?

No. It uses a fixed 1.5-second reaction time and a representative friction coefficient, so a real reconstruction needs measured values.

Does it model a gradient or a curve?

No. The total assumes level ground and a straight stop.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.