Cholesterol Ratio Calculator screenshot

Cholesterol Ratio Calculator

Compute total/HDL, LDL/HDL and non-HDL cholesterol from total, HDL and LDL values.

Privacy First
0 Runs
Updated 2026-11-06
No upload
Instant
No signup

Three cholesterol figures

Enter total cholesterol, HDL and LDL in mg/dL. The page prints total ÷ HDL, LDL ÷ HDL, and non-HDL cholesterol as total − HDL. The two ratios are unitless; the non-HDL figure carries mg/dL.

A total at or below the HDL is refused, because no non-HDL fraction exists and the ratio would divide by a non-positive number. The page prints the three figures and does not attach a risk band to any of them. This is arithmetic aid for a qualified reader, not a diagnosis or medical advice.

Each figure is a division or a subtraction on the values in the form. The same three numbers give the same output on every load, and nothing is transmitted.

The page computes three figures from total cholesterol, HDL and LDL in mg/dL: total ÷ HDL, LDL ÷ HDL, and the non-HDL difference total − HDL. The two ratios are unitless and the non-HDL figure is in mg/dL.

All three are printed with the divisions restated, so the arithmetic is auditable without re-deriving which side of each fraction each number sat on.

How to use it

Enter total cholesterol, HDL and LDL in mg/dL, then press Run. LDL may be zero but not negative; total and HDL must be above zero and the total must exceed the HDL. The output prints both ratios, the non-HDL figure, and the two divisions.

The arithmetic

With a total of 200, HDL 50 and LDL 130, the total/HDL ratio is 4, the LDL/HDL ratio is 2.6, and non-HDL is 150 mg/dL. Because both ratios divide by the same HDL, a change in HDL moves them in opposite directions relative to a change in the other numerator. Non-HDL is a subtraction, so it carries mg/dL rather than being unitless.

Where the page stops

The page does not label any of the three figures, does not compare them with a target, and does not estimate LDL — it uses the LDL you enter. A total at or below the HDL is refused, since the non-HDL fraction would be zero or negative.

What to Expect

Best for

  • Getting total/HDL, LDL/HDL and non-HDL from three figures already on a lipid panel.

What this tool keeps

  • All three results and both divisions are printed in one block.

What may need cleanup

  • Nothing: the printed lines are the complete output.

Sample input

total 200, HDL 50, LDL 130 mg/dL

Sample output

Total/HDL ratio = 4 LDL/HDL ratio = 2.6 Non-HDL cholesterol = 150 mg/dL Total ÷ HDL = 200 ÷ 50; LDL ÷ HDL = 130 ÷ 50

Frequently asked questions

How do I use the cholesterol ratio calculator?

Enter total cholesterol, HDL and LDL in mg/dL, then press Run. The page prints the total/HDL ratio, the LDL/HDL ratio, the non-HDL difference, and both divisions with your numbers.

Is anything uploaded when I press Run?

No. The arithmetic runs in this tab with JavaScript: nothing is posted to a server, nothing is stored, and reloading the page discards both the input and the result.

Why does the page want LDL as an input?

Because it computes ratios rather than estimating LDL. If you only have total, HDL and triglycerides, the Friedewald page on this site derives an LDL first; this page uses whatever LDL you give it and does not substitute one.

Is this a diagnosis or medical advice?

No. It is an arithmetic aid for a qualified reader: the page prints the formula's output and the numbers behind it, and leaves interpretation, and any decision taken from it, to someone qualified to make it. It is not a diagnosis and not medical advice.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.