SWOLF Calculator
Compute SWOLF from the length time and stroke count, with the pace per 100 metres alongside.
What this page does
SWOLF adds the seconds a length takes to the strokes it takes, so a lower number means a more efficient length: fewer strokes at the same speed, or more speed at the same stroke count.
How to use it
Enter this sample with the defaults shown:
30
Press Run. The page gives:
Length: 0:30 over 25 m
Strokes: 18
SWOLF: 48
Pace: 2:00 per 100 m
Basis: SWOLF = seconds + strokes for one length; it is comparable only at the same pool length
The formula and its basis
SWOLF = seconds for the length + strokes for the length. Pace per 100 m = seconds ÷ pool length × 100.
Seconds and strokes are as entered; SWOLF is only comparable at the same pool length, which the basis line states. Pace prints as m:ss and intermediate values are never rounded.
What it is not
This page is arithmetic on the numbers you enter, with each assumption stated: it is not financial, medical or training advice, and nothing is uploaded, stored or logged.
SWOLF adds the seconds a length takes to the strokes it takes, so a lower number means a more efficient length: fewer strokes at the same speed, or more speed at the same stroke count.
The rule this page applies: SWOLF = seconds for the length + strokes for the length. Pace per 100 m = seconds ÷ pool length × 100.
Basis: Seconds and strokes are as entered; SWOLF is only comparable at the same pool length, which the basis line states. Pace prints as m:ss and intermediate values are never rounded.
Worked example: the sample values below, with the defaults, give exactly the output recorded in What to Expect.
How to use the SWOLF Calculator
Enter length time in seconds in the box, set the options beside it, then press Run. The answer appears beside the form and re-runs on the same input.
Every number in the answer follows from your inputs and the assumptions stated below; the page does not choose a rate for you.
The worked example uses "30" with the defaults shown, and its exact output is printed in What to Expect.
The formula, its basis and its refusals
SWOLF = seconds for the length + strokes for the length. Pace per 100 m = seconds ÷ pool length × 100.
Seconds and strokes are as entered; SWOLF is only comparable at the same pool length, which the basis line states. Pace prints as m:ss and intermediate values are never rounded. Money prints to two decimals, percentages and ratios to four, and intermediate values are never rounded.
It refuses a length time of zero or less, a stroke count outside 0 to 200, and a pool length outside 15 to 100 metres.
What this page is not
It is arithmetic on the numbers you enter, with each assumption stated. It is not a training prescription, a medical measurement or a health-risk assessment, and it does not replace a coach or a clinician.
Where the tool is the wrong choice: A cross-pool comparison without adjusting for length; A stroke-technique assessment, which needs a coach.
What to Expect
Best for
- Tracking efficiency across a set
- Comparing a 25 m and a 50 m pool cautiously
- Checking whether a faster length cost more strokes
Not ideal for
- A cross-pool comparison without adjusting for length
- A stroke-technique assessment, which needs a coach
What this tool keeps
- The numbers exactly as you entered them
- The same answer on every run
- Nothing sent, stored or logged
What may need cleanup
- Units mixed between fields: enter kilograms and centimetres as each label says
- A comma used as a decimal separator, which the page refuses by name
Common errors
- It refuses a length time of zero or less, a stroke count outside 0 to 200, and a pool length outside 15 to 100 metres.
- A non-numeric value, which the page names rather than silently treating as zero
Example use cases
- Logging a swim session
- Testing whether a higher stroke rate helps
Sample input
30
Sample output
Length: 0:30 over 25 m Strokes: 18 SWOLF: 48 Pace: 2:00 per 100 m Basis: SWOLF = seconds + strokes for one length; it is comparable only at the same pool length
Who this is for
- Swimmers and triathletes
Frequently asked questions
What formula does this page use?
SWOLF = seconds for the length + strokes for the length. Pace per 100 m = seconds ÷ pool length × 100.
What does it refuse?
It refuses a length time of zero or less, a stroke count outside 0 to 200, and a pool length outside 15 to 100 metres.
What does this page not do?
It is arithmetic on the numbers you enter, with each assumption stated. It is not a training prescription, a medical measurement or a health-risk assessment, and it does not replace a coach or a clinician.
What rate basis and rounding does it use?
Seconds and strokes are as entered; SWOLF is only comparable at the same pool length, which the basis line states. Pace prints as m:ss and intermediate values are never rounded. Money prints to two decimals, percentages and ratios to four, and intermediate values are never rounded.
Why is SWOLF only comparable at one pool length?
Because a 50 m length takes more seconds and more strokes than a 25 m one. The page prints the pool length so the number is read in context.
Is a lower SWOLF always better?
At the same speed, yes. A very low SWOLF from gliding slowly is not automatically a faster swim, which is why the pace is printed beside it.
Build custom tools for your store
Join the SDK program to create useful ecommerce utilities for your store.