Countertop Calculator screenshot

Countertop Calculator

Counter run length times depth, plus waste, divided by the slab area you are buying.

Privacy First
0 Runs
Updated 2026-11-21
Runs in your browser
No sign-up, no upload

What the countertop calculator does

It computes the counter area from the run length and depth, adds waste and divides by the slab area: area = run length × depth; with waste = area × (1 + waste ÷ 100); slabs = with waste ÷ slab area, rounded up.

The slab area is a control because it is the product you are buying, not a standard the page can assume. The same is true of the depth: 600 mm is common but not universal, and the page uses the number you type. Each figure is printed so the order can be checked against the drawing.

In the sample a 3 m run at 0.6 m deep is 1.8 m2; 10 % waste makes 1.98 m2; at 4.5 m2 per slab that is one slab.

A part slab counts as a whole slab, which is what you have to buy. The page is ordering arithmetic, not a fabrication drawing: it does not lay out seams, sink cut-outs or edge profiles, and the basis line says so. A run length, depth or slab area of zero and a waste allowance above 50 % are each refused by name.

How to use it

Set Run length, Counter depth, Slab area and Waste.

Press Run. The result prints the counter area, the area with waste and the slab count.

Worked example

Input with the defaults:

3 m run, 0.6 m deep, 4.5 m2 slab, 10 % waste

Output:

Counter area:          1.8 m2 (3 × 0.6)
With waste:            1.98 m2 (10 %)
Slabs:                 1 × 4.5 m2

Why it runs in your browser

The arithmetic runs in this tab. Your measurements are never uploaded.

The page multiplies the counter run length by its depth, adds waste and divides by the slab area you are buying.

Run length, depth, slab area and waste are all controls, and the result prints each one so the order can be checked against the drawing.

Area first, slabs second

Area = run length × depth, and a part slab counts as a whole slab because that is what you buy. The page prints the area, the area with waste and the slab count separately, so a disagreement with a fabricator can be traced to the depth, the waste or the slab size rather than to the result as a whole.

The page does not lay out seams, sink cut-outs or edge profiles. Those change how a slab is used, and a page that ignored them would overstate its own precision. It is ordering arithmetic, and the basis line says so.

How to use Countertop Calculator

Set Run length, Counter depth, Slab area and Waste.

Press Run. The result prints the counter area, the area with waste and the slab count.

What to Expect

Best for

  • Ordering countertop material by area
  • Checking a fabricator's slab count against an area
  • Comparing two depths on the same run

Not ideal for

  • A fabrication drawing with seams, cut-outs and edge profiles
  • An L-shaped run, which must be split into rectangles
  • A price, which needs a material rate the page does not take

What this tool keeps

  • Every dimension and slab area you typed
  • The waste percentage applied

What may need cleanup

  • Depth measured in millimetres, which must be converted to metres
  • An overhang that changes the effective depth

Common errors

  • Forgetting that a part slab must be bought whole
  • Counting a sink cut-out as removed area when it is not

Example use cases

  • Ordering a kitchen countertop
  • Checking a quote's slab count
  • Estimating a bathroom vanity top

Sample input

A 3 m run at 0.6 m deep, 4.5 m2 slabs and 10 % waste.

Sample output

A 1.8 m2 counter, 1.98 m2 with waste and one slab.

Who this is for

  • Homeowners planning a kitchen
  • Fitters checking an order

Frequently asked questions

Why is a 1.98 m2 counter one slab of 4.5 m2?

One slab is larger than the area with waste, so one is enough by area. Whether that slab can be cut to cover the run with its seams and cut-outs is a fabrication question the page does not answer.

Does the page account for a sink or a hob cut-out?

No. A cut-out removes material from the slab without reducing the slab you must buy, so subtracting its area would understate the order. The page prints area and slabs and says it is not a fabrication drawing.

What depth should I use?

The finished depth of your counter, which is usually 0.6 m but not always. Depth is a control; the result prints the figure it used so a non-standard run is not silently treated as standard.

Developer program

Build custom tools for your store

Join the SDK program to create useful ecommerce utilities for your store.