Crown Moulding Calculator
Room perimeter plus a mitre allowance for each outside corner, plus waste, in stock lengths.
What the crown moulding calculator does
It computes the room perimeter, adds the mitre allowance you set for each outside corner, adds waste and divides by the stock length. Perimeter = 2 × (length + width); mitre allowance = outside corners × allowance per corner; with waste = (perimeter + mitre) × (1 + waste ÷ 100); stock lengths round up.
Crown moulding needs a longer piece at an outside corner than the wall measures, because the cut runs around the corner. How much longer depends on the profile and the saw, so the allowance is a control rather than a constant the page invents. An inside corner needs no extra length.
In the sample a 5 m × 4 m room has an 18 m perimeter; two outside corners at 0.1 m each add 0.2 m; 10 % waste makes 20.02 m; at 3 m per length that is 7 lengths.
The page is ordering arithmetic, not a code check. A fractional corner count, a negative allowance, a stock length of zero and a waste allowance above 50 % are each refused by name.
How to use it
Set Room length, Room width, Outside corners, Mitre allowance, Stock length and Waste.
Press Run. The result prints the perimeter, the mitre allowance, the length with waste and the stock lengths.
Worked example
Input with the defaults:
5 m × 4 m, 2 outside corners, 0.1 m allowance, 3 m stock, 10 % waste
Output:
Perimeter: 18 m (2 × (5 + 4))
Mitre allowance: 0.2 m (2 outside corners × 0.1 m)
With waste: 20.02 m (10 %)
Stock lengths: 7 × 3 m
Why it runs in your browser
The arithmetic runs in this tab. Your room measurements are never uploaded.
The page computes the perimeter, adds the mitre allowance you set for each outside corner, adds waste and divides by the stock length.
The allowance is per corner and is a control, because how much longer an outside corner needs depends on the profile and the saw rather than on a constant.
Why an outside corner needs extra length
An inside corner turns within the wall line; an outside corner wraps around it, so the moulding runs past the measured wall by roughly its own depth. The page takes that extra as a per-corner allowance you type, multiplies it by the outside-corner count and adds it to the perimeter before waste.
Inside corners need no allowance here. The page counts only the outside corners you name, and prints the total allowance beside the perimeter so the addition is visible.
How to use Crown Moulding Calculator
Set Room length, Room width, Outside corners, Mitre allowance, Stock length and Waste.
Press Run. The result prints the perimeter, the mitre allowance, the length with waste and the stock lengths.
What to Expect
Best for
- Ordering crown moulding for a rectangular room
- Comparing a mitre allowance at two values
- Checking a quote's linear metres
Not ideal for
- A room with bay walls, which needs each run measured
- A profile whose mitre length you have not measured
- A code or fire-rating question
What this tool keeps
- Every dimension and allowance you typed
- The stock length and waste the count used
What may need cleanup
- Corner counts that include inside corners
- Allowances measured in inches, which must be converted to metres
Common errors
- Counting inside corners as outside corners
- Applying the allowance after waste instead of before
Example use cases
- Ordering crown for a living room
- Checking a carpenter's allowance
- Planning a room with two outside corners
Sample input
A 5 m × 4 m room, 2 outside corners, a 0.1 m allowance, 3 m stock and 10 % waste.
Sample output
An 18 m perimeter, a 0.2 m mitre allowance, 20.02 m with waste and 7 stock lengths.
Who this is for
- Homeowners planning a ceiling trim
- Carpenters checking an order
Frequently asked questions
Why is the crown count 7 lengths where the baseboard count was 8?
The stock length is different. The crown sample uses 3 m per length, so 20.02 ÷ 3 is 6.67 and rounds up to 7; the baseboard sample uses 2.4 m per length for a shorter total.
How large should the mitre allowance be?
It depends on the profile and the saw, which is why it is a control. Measure a scrap cut around an outside corner, or ask the supplier, and type the figure; the page multiplies it by the corner count.
Do inside corners need an allowance?
Not on this page. An inside corner turns within the measured wall line, so the length is already in the perimeter. Only the outside corners you name add to it.
Build custom tools for your store
Join the SDK program to create useful ecommerce utilities for your store.